Have you tried the Dream Coil topper yet?
| I can't remember who ordered the Carpenter Dream Coil PU topper from Penneys besides me. I'm wondering if you had a chance to try it out. If so, how did you like it...or not? Mine is still in the package. I just haven't felt like adding another topper to my mattress right now. It's been feeling too good to mess with it! :) But, I don't think I'll take it back. If I don't end up using it on top of our bed, I can either cut it and use it inside, or maybe as a camping pad. I think my back will respond better to a PU foam topper vs. memory foam or latex. |
Re: Have you tried the Dream Coil topper yet?
|
Well, I needed to change the sheets today so I went ahead and put the Carpenter Dream Coil topper on. I'm not sure if my side of the bed will be too soft for it, but I'll find out tonight. My husband's configuration is a bit firmer and might be a better match. We'll see! The inside of his mattress is from the bottom up: LuraFlex coils surrounded by a high density firm PU foam edge 55 ILD 3/4" HR PU foam 45 ILD 3/4" HR PU foam 44 ILD talalay latex 1 inch Zippered quilted cover with fiberfil My mattress: LuraFlex coils surrounded by high density firm PU edge 55ILD 3/4" HR PU foam 32 ILD talalay latex 1 inch 32 ILD talalay latex 1 inch Zippered quilted cover with fiberfil *********************************************** I'll see how it goes tonight and I may just exchange a 32 ILD latex for a 44 ILD and leave the 55 ILD PU foam in as the base. Or I could do the same configuration as my husband's, but would prefer to stay with 2" of latex if I can. I'll report back. By the way, what type of feel would I get if I were to put the 44 ILD on TOP of the 32 ILD latex, as opposed to the other way around? I know Lynn might have mentioned doing it that way. This message was modified Mar 2, 2008 by BeddyBye
|
Re: Have you tried the Dream Coil topper yet? I finally did and I liked it!
|
I slept on the Dream Coil last night and as of now, I'm giving it a two thumbs up. I didn't even have to configure my mattress to make it firmer, either. I like the more stable feel of this pad compared to the way latex feels under my body. It didn't feel jiggly-bouncy or marshmallow-squishy like latex and memory foam do. It just felt "right there". I think my body prefers the feel of HR PU foam on its back vs. latex and memory foam. And, it's not so thick that it caused me to sink in too much. I also liked the fact that it didn't feel like a separate topper. Instead, it felt like it was part of my mattress. And having a King size is nice to lay over our two XL Twin mattresses to tie it together even more. I put my CuddleBed Ultimate fiber mattress topper over it. What a great combination! So, I'm going to keep it on and see how it goes. I wonder if Carpenter stands behind its claim that this pad won't go flat. Must be the Omalon which is used in rug pads. I can handle that! Also, the smell of it coming out of the package didn't bother me at all. It doesn't have that nasty, toxic odor that I find with memory foam. But, I realize some people are more sensitive than others. This message was modified Mar 2, 2008 by BeddyBye
|
Re: Have you tried the Dream Coil topper yet?
|
BeddyBye wrote: Well, I needed to change the sheets today so I went ahead and put the Carpenter Dream Coil topper on. I'm not sure if my side of the bed will be too soft for it, but I'll find out tonight. My husband's configuration is a bit firmer and might be a better match. We'll see! The inside of his mattress is from the bottom up: LuraFlex coils surrounded by a high density firm PU foam edge 55 ILD 3/4" HR PU foam 45 ILD 3/4" HR PU foam 44 ILD talalay latex 1 inch Zippered quilted cover with fiberfil My mattress: LuraFlex coils surrounded by high density firm PU edge 55ILD 3/4" HR PU foam 32 ILD talalay latex 1 inch 32 ILD talalay latex 1 inch Zippered quilted cover with fiberfil *********************************************** I'll see how it goes tonight and I may just exchange a 32 ILD latex for a 44 ILD and leave the 55 ILD PU foam in as the base. Or I could do the same configuration as my husband's, but would prefer to stay with 2" of latex if I can. I'll report back. By the way, what type of feel would I get if I were to put the 44 ILD on TOP of the 32 ILD latex, as opposed to the other way around? I know Lynn might have mentioned doing it that way.
As to the feel of the 44ILD on top of the 32 ILD, I found that sometimes this type of combination can improve the feel. The guy at flobeds years ago had us try something like this. It's worth a try. The CuddleBed Ultimate fiber mattress you speak of - it appears to not be available at CostCo any more. But this one says it is polyester filled- is that the same thing you have? http://tinyurl.com/yvdocm This message was modified Mar 2, 2008 by jimsocal
|
Re: Have you tried the Dream Coil topper yet?
|
Actually, it's not that hard at all. Comfortably firm. And with the CuddleBed fiber topper, it makes it even nicer. I still see it at Costco. It's on sale, too, through March 9. Here's the link: http://www.costco.com/Browse/Productgroup.aspx?Prodid=11189730&whse=BC&Ne=4000000&eCat=BC|62415|28683|492&N=4018505&Mo=18&pos=2&No=1&Nr=P_CatalogName:BC&cat=492&Ns=P_Price|1||P_SignDesc1&lang=en-US&Sp=C&ec=BC-EC14142-Cat28683&topnav= Our twin mattresses are inside a King frame and we have the same bedding on both. King size sheets, blankets, comforter, etc. So even though we each have our own XL Twin mattress, everything else is shared. I stay on my own side, though. And, likewise for him. He's fast asleep by the time I get to bed! Also, besides the pillow under my head, I have one pushed against my back and under my knees when I'm laying on my side. I would feel lost without them. Romantic, eh! :-) I might have to give that 44 ILD over the 32 ILD a try if I find my current configuration won't work. jimsocal wrote: Wow, your husband's bed must be like a rock! That would kill me. (Glad to know another couple who have twins side by side as we do. I think people think it's weird but my wife has restless leg syndrome AND is always hot where I am always cold, so sleeping in the same bed with the same covers just doesn't work for us.)</p><p>As to the feel of the 44ILD on top of the 32 ILD, I found that sometimes this type of combination can improve the feel. The guy at flobeds years ago had us try something like this. It's worth a try.</p><p>The CuddleBed Ultimate fiber mattress you speak of - it appears to not be available at CostCo any more. But this one says it is polyester filled- is that the same thing you have? <strong>http://tinyurl.com/yvdocm</strong></p><p><strong></strong> |
Re: Have you tried the Dream Coil topper yet? I bought two more (XL TWINs are on sale!)
|
I had another comfortable night on the Dream Coil mattress pad. I really like this thing! In fact, I notice JC Penney only has one size left---XL Twin. It's on sale for $29.99. So, I bought two more with a $10 off promo. Actualy, I had ordered one with a 15% off coupon and then noticed the other promo. So I quickly called and the lady gave me BOTH coupon codes! That took off $19.00 from the order. I figure I might try one INSIDE my mattress instead of one of my 32 ILD latex layers just to see if it makes a difference in the feel of my mattress. Heck, if I like it, I might do away with the latex altogether! After all, these are guaranteed by Carpenter to never go flat--a lifetime warranty. We'll see how I like the way it feels inside. I honestly think I like the feel of HR PU better on my back than I do latex, for the most part. I'm NOT talking about memory foam or those cheap, eggcrate toppers. But, maybe the combination of one inch of talalay latex and the Dream Coil inside my mattress with another Dream Coil as a topper will be the match made in heaven. We shall see! I can always use it for the inside of my husband's mattress if need be. Or as a topper for my daughter's bed. Either way, I think I got a good deal. I highly recommend it for someone who wants to use a nice layer of PU foam inside their mattress configuration. |
Re: Have you tried the Dream Coil topper yet?
|
Seems like they are pretty much sold out so I guess it's a moot point, but what kind of foam is it made out of? Sounds like some kind of HR if it doesn't flatten out. I think there's a lot to be said for HR foam. It's very flexible in how it can be used, it lasts a long time without softening up and developing body impressions and it's both supportive and passive, which makes it easy to sleep on for people with lumbar issues or other conditions. I still think the latex on your bed is contributing to your back pain, so you may well find that replacing a layer of it with the Dream Coil is more comfortable for you. |
Re: Have you tried the Dream Coil topper yet?
|
Here is Carpenter's website explaining the Dream Coil and Omalon (what it's made of:) I notice that Omalon is also used in 6" cores for certain types of mattresses, often the base used under memory foams and air-beds. It looks like it comes in different densities. Obviously, the pad I have is on the softer side for comfort. But nothing like latex or memory foam! http://www.carpenter.com/Divisions/bedding_omalon.htm http://www.carpenter.com/Divisions/consumerprod_foam.htm As for the latex inside my bed...as long as it's just that---INSIDE, and in minimal amount. I found that I cannot use it as a topper. I also need the HR PU base, as well as the LuraFlex coil springs. I wouldn't a good candidate for an all-latex mattress kit or otherwise. I NEED my springs and some high density HR PU foam. As it is now, with the Dream Coil on top, I rather like the way the two 32 ILD latex layers (total of 2") feel INSIDE my mattress. I might exchange one layer for the XL Twin Dream Coil pad when it arrives. But, for now, this seems to be a great combination. I woke up today feeling just as refreshed as I have the last few nights. In fact, this morning, I lay there savoring the unique, comfortable and supportive texture of the Dream Coil pad underneath my body. VERY nice! cloud9 wrote: Seems like they are pretty much sold out so I guess it's a moot point, but what kind of foam is it made out of? Sounds like some kind of HR if it doesn't flatten out. I think there's a lot to be said for HR foam. It's very flexible in how it can be used, it lasts a long time without softening up and developing body impressions and it's both supportive and passive, which makes it easy to sleep on for people with lumbar issues or other conditions. </p><p>I still think the latex on your bed is contributing to your back pain, so you may well find that replacing a layer of it with the Dream Coil is more comfortable for you. |
Re: Have you tried the Dream Coil topper yet?
|
BeddyBye wrote: Actually, it's not that hard at all. Comfortably firm. And with the CuddleBed fiber topper, it makes it even nicer. I still see it at Costco. It's on sale, too, through March 9. Here's the link: http://www.costco.com/Browse/Productgroup.aspx?Prodid=11189730&whse=BC&Ne=4000000&eCat=BC|62415|28683|492&N=4018505&Mo=18&pos=2&No=1&Nr=P_CatalogName:BC&cat=492&Ns=P_Price|1||P_SignDesc1&lang=en-US&Sp=C&ec=BC-EC14142-Cat28683&topnav= Our twin mattresses are inside a King frame and we have the same bedding on both. King size sheets, blankets, comforter, etc. So even though we each have our own XL Twin mattress, everything else is shared. I stay on my own side, though. And, likewise for him. He's fast asleep by the time I get to bed! Also, besides the pillow under my head, I have one pushed against my back and under my knees when I'm laying on my side. I would feel lost without them. Romantic, eh! :-) I might have to give that 44 ILD over the 32 ILD a try if I find my current configuration won't work.
For me it's too hard for a topper. Maybe under the fibre cushion as you are using it, it might be fine, but I can't sleep right on top of it, it's too hard for me that way. I might give it another chance under my wool topper. Last night I slept with just my 2" wool topper doubled up on top of my hr foam and that was pretty good. The night before I had |
Re: Have you tried the Dream Coil topper yet?
|
You have the Dream Coil mattress pad? At first I thought you meant the Cuddlebed Ultimate! Maybe that does make the Dream Coil a bit softer. I don't know. I'm not going to try it, either! :) "If it ain't broke, don't fix it!" LOL This morning I woke up PAIN FREE! And, I even managed to go all day without my sacroiliac bothering me. Oh, I realize that with a chronic pain like that, it comes and goes. But, at least at the moment I'm not going to blame my mattress or the Dream Coil. :) jimsocal wrote: Actually, I have one of these! Bought it years ago! I just didn't realize what it was called until I looked at your link. I remember buying it at JCP now. And no, it has not gone flat <BR>(though I've had it stored away mostly.) It's in our collection of "toppers". </p><p>For me it's too hard for a topper. Maybe under the fibre cushion as you are using it, it might be fine, but I can't sleep right on top of it, it's too hard for me that way.</p><p>I might give it another chance under my wool topper. Last night I slept with just my 2" wool topper doubled up on top of my hr foam and that was pretty good. The night before I had <BR>the wool topper AND the mattress top topper (which I cut off the top of the mattress) and the two of those together was way too much softness and my lower back killed me the next<BR>morning. |
Re: Have you tried the Dream Coil topper yet?
|
BeddyBye, thanks for the Omalon link. Sounds really interesting. Now I'm sorry I missed my chance to order one while they still had my size. I just figured I had a closet full of foam I'm not using at the moment and this would just be another addtion to the collection. It looks really cool too. Someone mentioned carpet padding, and I wonder if the topper is the same as the Omalon carpet pad, only prettier. I'm always looking for a way to make the mattress a little more rigid without making it quite as hard as the carpet remnant does. Now I'm REALLY jealous of your mattress! |