Got my foam layers from SleepEZ
|
I got my foam today. Haven't tried laying on it yet. Took some photos which I will post tomorrow probably in this thread. Not entirely thrilled with the firmness and quality of the latex. One of the pieces has a fair amount of imperfections and the other piece has a glued seam all along the vertical length of the twin, about 2 and 1/4" in from the edge. It's a very hard seam from the glue and I think if I were to lay on it I would feel it, even under, say, a wool topper. If it were a King size I could understand the need for a glued seam, but a twin? Seems a bit sketchy to me. Also, this following problem is not at all SleepEZ's fault, unless what they are selling as a 32ILD is nowhere near that, but I already had a piece of 3/4"-1" latex that I estimated to be about a 24ILD. So I ordered a medium Talalay 1" thinking it would be better for support. But the one I got from SleepEZ seems to be just as soft as the one I have already; so either I estimated wrong (most likely) or they sent me something on the very low end of "Medium" (listed at their site as 32). So I would not have bought that piece had I known it was going to be pretty much exactly like the piece (actually I have 2 like this) that I already have. This is the piece with the seam as well. The Dunlop piece seems a LITTLE more firm than that and is 1.5" so it may work for me. Also it is exactly 1 and 3/4 inches thick not 1½, so that is good in my case, I think. However, I do think they should be more exact on their site about the thickness. Could be that someone really wants exactly 1½ inch, not 1 and 3/4 inch... I mean, why not describe it on the site as it is? I'll try sleeping on the Dunlop 1 and 3/4" natural "Medium" ILD tonight and see how it feels and report back with a "first night's impression" tomorrow probably. Also I'll post the photos of the imperfections and get you guys' and girls' opinions on whether or not it is within the realm of acceptable or not considering these are not discounted prices. And just fyi, this is the first latex I ever bought that did not come compressed. It was just rolled and covered in plastic in a big box. Maybe they only compress the bigger pieces...? This message was modified Jan 27, 2010 by jimsocal
|
Re: Got my foam layers from SleepEZ
|
Okay this is my last post in this thread unless someone happens to post something that warrants a response. I just wanted to finish out a full week of updates. 7th NIGHT REPORT: I had a very sore back last night before I went to bed. The bending over and reaching I've been doing to clean the apartment has really made my back and shoulders sore. So I did have a little pain during the night but it obviously was caused by the work I did the previous days, not the mattress itself. I woke up once again with none of that lower or mid-back pain that I was getting before I re-configured my mattress as above with the Talalay latex replacing the old HR foam. So this configuration (as in my last post) is a keeper. This teaches me a lesson: If the mattress starts to hurt when it didn't before, one of the layers may have given out. In this case it was my 1" HR foam layer that was maybe 3 years old. I expected it to last years longer, and that's why I did not suspect it was the problem for quite a while. Someone here on the forum suggested to me that this might be the problem and so I tried it and she was right! So HR foam apparently does not last a long time like it's supposed to. By the way, this HR foam had not even been in the same place for a long time. That is, it was a layer that I often changed out for a different piece (different firmness) and I'm sure it got rotated and even flipped at times when I changed it, so really it had a very short life span. I can no longer recommend HR foam unless it is for someone who just cannot afford latex and is willing to use something they know won't last past a few years. It is however very cheap if you get it from a warehouse as I did, so the investment was minimal and I got my money's worth out of it. Also, note that someone with no back or sleep issues might be able to use it for a longer time and not notice that it had "given out" as I did. My back is very sensitive to any lack of support so I noticed something was wrong whereas someone else might have not noticed it until a year or more later... maybe. This message was modified Feb 3, 2010 by jimsocal
|