| For those with latex mattresses with split core layers for individual comfort on each side - is there ever an issue with the seam between the two sides? Do the pieces ever move around on you, does it open up a little, or can you feel the seam when lying on it? |
| P.S. The reason I don't always sleep in the middle of the bed is I like to be able to reach for a tissue if I need it or a sip of water and I can't reach the night stands unless I sleep on the end of the bed but as I said, have slept in the middle of the bed and when I do that, I place the tissue box on the bed to be near it. |
| How much would you say the mattress cover contributes to the cores staying together - would a stretchy cover like terry cloth work, or would you need a firmer tighter cover, like quilted cotton? |
| Proof1st, I am not sure since I always slept with the latex cores inside my zippered cover but I know they are heavy and a tight fit. |
| For those interested, per a conversation with SleepEZ, they recommend a 1-piece top layer if you choose their stretch cover instead of the quilted cover. This would be to eliminate feeling the seam, because they say there wouldnt be any movement of layers being rubber, and heavy, etc. |
|
From my disgruntled opinion of complete latex beds, you can completely feel the seam. With the convoluted topper and the fabric covering, you can even frequently see the seam. You lay on one side of it, it pushes that latex core down, and it 'sticks' up against the one next to it. You get off the bed, it stays stuck, and you have a distinct line running down your bed. In my opinion, I feel like I 'fall' towards the middle of the bed where the cores come together down the middle. I hate it and have been trying to tolerate it for almost two years now. Chris |
|
texfire wrote: From my disgruntled opinion of complete latex beds, you can completely feel the seam.
With the convoluted topper and the fabric covering, you can even frequently see the seam. You lay on one side of it, it pushes that latex core down, and it 'sticks' up against the one next to it. You get off the bed, it stays stuck, and you have a distinct line running down your bed. In my opinion, I feel like I 'fall' towards the middle of the bed where the cores come together down the middle. I hate it and have been trying to tolerate it for almost two years now. Chris Sounds like you have a FloBed with the convoluted topper over the split cores - and you have a quilted cover? Have you tried a full 3" layer in one piece over the split cores? Maybe that would help, being more substatial than the convoluted layer. I think that is basically what sleepez recommended when using a stretchy cover - the top layer, full thickness, with no seam. Thanks again for posting - your experience needs to be added to the mix of factors for those considering a split core mattress. Hope you can find a solution! |
|
proof1st wrote: Chris - sorry to hear of your experience - but thanks for posting. Its funny that Ive searched this forum for info on the very issue you are having, yet never found your previous posts. I was suprised that more people dont have a problem with the seam, I assumed it had to be a problem sometimes. Sounds like you have a FloBed with the convoluted topper over the split cores - and you have a quilted cover? Have you tried a full 3" layer in one piece over the split cores? Maybe that would help, being more substatial than the convoluted layer. I think that is basically what sleepez recommended when using a stretchy cover - the top layer, full thickness, with no seam. Thanks again for posting - your experience needs to be added to the mix of factors for those considering a split core mattress. Hope you can find a solution! I do have a Flobed with the convoluted topper over the split cores. My cover is whatever comes standard that zips around the edge. It's fine quality, but not thick. I've talked to Flobed about it and they recommended I use Spray adhesive to laminate the two cores together. I tried it. It's unwiedly and difficult to get lined up properly so I ended up not with 100% adhesion. It didn't help much and when I re-opened my bed, parts had come apart and parts were still stuck together. I'm sure I did a sub-par job of putting them together... but you can't do it in the bed, cause adhesive gets on the layers underneath, so I tried to do it on the kitchen floor and protect the floor with paper and it was just a mess. I'm unaware there is a 3 inch solid layer I can lay across (at least in a CA King). So I haven't tried that. This bothers me but moreso that I can't find the combo of layers that works for me. I have med/firm/superfirm layers and several of each and can't get something that doesn't hurt my low back but also feels comfortable to lay on, back and side. At the moment, I'm firm and trying to go softer. Now I'm F/F/SF and will probably switch to M/F/SF, although last time I did M/F/F it hurt my back. Nevertheless Flobeds has been responsive to listening to me bitch and they've offered suggestions. Unfortunately, every time I go to a hotel, I feel much better at first and in the morning in the hotel bed. It's either real, or I have a psychological problem which is affecting my judgement. I think it's about to be unsolvable, so I'm looking into innerspring beds, or combo innerspring with latex. However, they don't talk much about those here and I can't find any good place to separate the good from the bad (if there is good).
Chris |
|
Well I know you can get the seamless layers in that size, if you want to try that route (they can be pricey in Cal King): http://www.sleepez.com/catalog/product_info.php/cPath/27/products_id/156 http://www.sleeplikeabear.com/product/TX-02-CK And of course Flobeds has the components of their mattresses - even if they don't normally do a non-split core, their suppliers make them, so they can get them - I would try to keep working with Flobeds. Flobeds Medium is 28 ILD, so there is room to go softer. Have you tried a soft top layer? - and I dont mean the convoluted - I would disregard that since its not helping you. I would ask Flobeds to send you a soft 19 ILD 3" layer with no seam. They say they work with you till youre happy - and for the money you spend they should. |
|
proof1st wrote: Well I know you can get the seamless layers in that size, if you want to try that route (they can be pricey in Cal King):
http://www.sleepez.com/catalog/product_info.php/cPath/27/products_id/156 http://www.sleeplikeabear.com/product/TX-02-CK And of course Flobeds has the components of their mattresses - even if they don't normally do a non-split core, their suppliers make them, so they can get them - I would try to keep working with Flobeds. Flobeds Medium is 28 ILD, so there is room to go softer. Have you tried a soft top layer? - and I dont mean the convoluted - I would disregard that since its not helping you. I would ask Flobeds to send you a soft 19 ILD 3" layer with no seam. They say they work with you till youre happy - and for the money you spend they should. Chris |
|
texfire wrote: Chris |