the problem with solid latex pillows
| Okay, here is why I think a lot of people have problems with them. Because of the bounce back (push back) feature of latex, it is extremely difficult to get the exact softness/loft combination to align your head properly with your back. With the two solid latex pillows I've tried so far, one held my head slightly too high and was not soft enough for me and the other let me go to low. Its softness felt great (didn't push back on my jaw too hard) but the position in which my head was held was not right. Last night, I tried placing a folded towel under the soft one (LI Rejuvenite pillow) and it placed my head in the perfect position while maintaining the softness. This lack of adjustability is why some have tried the granulated latex pillows, but some say that the granules tend to disperse in the night. Maybe what we need is a "FloPillow" system, where you can try various thin layers of latex of different firmness? |
Re: the problem with solid latex pillows
|
How would a "kit" pillow work? If you take a solid latex pillow and slice it into layers, each layer will be a different size. A pillow made of latex layers all the same size would have the shape of a brick. I suppose you could have just two pieces, "cores" and the outer clam-shaped pieces, but in order to provide different lofts, the cores themselves would have to be maybe 1" slices or something, and you would need a different pillowcase for each loft. Given the fabrication costs and "inventory" issues, such a pillow would be very expensive if it were to be profitable to sell. How about bags of shredded latex in different densities? I have never slept on a shredded latex pillow, so I don't know if this makes any sense at all, I'm just trying to think outside my little box. |
haysdb: the problem with solid latex pillows
| haysdb, I think you are right, a latex kit type of pillow will not be cost effective to make and the most they could do is have latex pieces to unzip and put inside to get the height and firmness. I never tried latex pieces before and always used solid latex for my pillow but it is something I could consider one day. |
Re: the problem with solid latex pillows
|
Are solid latex pillows measured in terms of loft and ILD? I've been perusing websites, and so far have only come across one that mentioned an ILD, which they said was between 10 and 15. If I knew the ILD of the Nuform pillow at Bed, Bath & Beyond, at least I would know what is way too firm. The loft would probably be OK if the pillow were a lot softer. My head hardly sunk in at all but just laid there on top of the pillow like it was a balloon. There definitely has to be a better way to finding the right pillow. |
Re: the problem with solid latex pillows
| An update on my quest for the perfect latex pillow. As you may have seen in another post, I tried the Posturpedic solid latex and was disappointed yet again. So I created my own home-made shredded pillow by picking the Posturpedic into little pieces and placing them in its zippered cover. This has worked pretty good, but the night before last, I felt like it had a little too much loft. So for last night, I pulled out a good sized handful of the shreds. I slept very well, without the "too high feeling." I do believe someone could sell a shredded latex kit that allows you to readily adjust the amount of latex. ILD firmness of the shreds would also be an interesting adjustment, but would probably be a little expensive for the average consumer. |
Re: the problem with solid latex pillows
|
Some sort of adjustability needs to be provided. I was researching Kapok pillows and found one place that sells it by the pound along with zippered covers in three sizes. That's the closest thing I have seen to a "kit" pillow. |
Re: the problem with solid latex pillows
|
Isn't this what we're talking about? Down Encased Triple-Select Latex Pillow |
Re: the problem with solid latex pillows
| Wow! So there is a "FlowPillow". I still think I would like my $40 shredded latex pillow better. |