PU/Latex/Memory Foam Mattress
|
Has anyone put together a mattress with PU base, latex in the middle, and memory foam on top? I was laying on a Simmons ComforPedic the other day with this configuration. It felt like Temperpedic support laying in it, but it didn’t have that hard feel when you roll over or sit on it – it actually had a little spring to it. When I was looking at it in a showroom, I was able to see some of the specs on the sheet the sales person was holding: Top layer: 4.5” 5.5lb memory foam – ILD unknown, but possibly 2 different foam ILDs (springs back faster than Temperpedic) Middle layer: 2" 24 ILD latex (said it was to dissipate heat) Bottom: 7" 30 ILD foam (I'm assuming it's PU, but I'm not sure???) From what I've been reading about foam lately, I thought a combination like this would be too soft, but it was really supportive. After laying in it for awhile, it did seem a lot cooler and more comfortable than a Temperpedic. The price for the above configuration was $4200. Any ideas on putting one together for a lot cheaper? |
Re: PU/Latex/Memory Foam Mattress
|
Well, I decided to put my new Makita 12" compound sliding miter saw to good use this weekend and build my own mattress foundations. I basically used 1x4's laying flat for the framing around the top and bottom where the slats will rest and the foundation sits on the bed frame. I spaced 2x4's at 12" between the 1x4's and will wrap the sides in 1/2" OSB. I figure my total cost will be around $75 by the time I'm done...depending on the price of the fabric to wrap around them. I'm planning on using 4x1's for the slats (actual size is 3.5 x .75) - but I'm not sure what the recommended gap between the slats is. Any ideas? I placed an order at Foam Factory Thursday for 4" LUX and 3" HD36, but I still haven't received a ship notification. I did email them on Saturday to let me know when it will ship and to make sure they ship the high density. I will be sure to weigh them when (or if) I get them. |
Re: PU/Latex/Memory Foam Mattress
| FBM doesn't send any communications. Not order confirmations, not shipping notices, nothing. |
Re: PU/Latex/Memory Foam Mattress
| Hmmmmm... I think I'll keep emailing then. |
Re: PU/Latex/Memory Foam Mattress
|
steve2u wrote: I'm not sure what the recommended gap between the slats is. Any ideas? I used 1.5" for slat spacing between slats, and it works great. |
Re: PU/Latex/Memory Foam Mattress
|
Error This message was modified Nov 27, 2007 by steve2u
|
Re: PU/Latex/Memory Foam Mattress
|
Update: I received my foam from FBM and it was the correct density - it's sad that I'm surprised at this. The foundation construction is going a little slower than expected, but they should be pretty strong. Here's a link to a few pictures: http://www.visi.com/~stevet/bed.html I'm still thinking about returning my Sensus topper. I noticed this morning that the spot where I slept throughout the night was like Jello an hour after I got out of bed. The edges of the bed were much more firm. I think that the Sensus topper may be too sensitive to heat for me - it just doesn't seem like it could offer adequate support when it's that soft. This message was modified Nov 27, 2007 by steve2u
|
Re: PU/Latex/Memory Foam Mattress
| How would 3" of FBM 32 ILD latex compare to my 3" Sensus topper? It sounds like latex is generally softer than poly at the same ILD. I'm a little gun shy about going too soft now. I rather be on the firm side and add soft poly or something else on top of the latex if needed. I may even try sleeping on my 36 ILD poly with a comforter under me (for a little extra softness) for a few days. This may be a little bit hard for side sleeping, but I seem to keep waking up on my stomach with the Senus topper for some reason, so it probably won't matter. |
Re: PU/Latex/Memory Foam Mattress
|
A couple of my recent posts were not viewable unless you hit "all" to view the entire thread. Sorry if there's repeats in your browser, but here they are again: Update: I received my foam from FBM and it was the correct density - it's sad that I'm surprised at this. The foundation construction is going a little slower than expected, but they should be pretty strong. Here's a link to a few pictures: http://www.visi.com/~stevet/bed.html I'm still thinking about returning my Sensus topper. I noticed this morning that the spot where I slept throughout the night was like Jello an hour after I got out of bed. The edges of the bed were much more firm. I think that the Sensus topper may be too sensitive to heat for me - it just doesn't seem like it could offer adequate support when it's that soft. How would 3" of FBM 32 ILD latex compare to my 3" Sensus topper? It sounds like latex is generally softer than poly at the same ILD. I'm a little gun shy about going too soft now. I rather be on the firm side and add soft poly or something else on top of the latex if needed. I may even try sleeping on my 36 ILD poly with a comforter under me (for a little extra softness) for a few days. This may be a little bit hard for side sleeping, but I seem to keep waking up on my stomach with the Sensus topper for some reason, so it probably won't matter. |
Re: PU/Latex/Memory Foam Mattress
|
Fascinating thread this has been, Steve... So, I've been thinking about the following: 2" Foamex Venus 3" FBM Talalay 20ILD 3" FBM HD36 HQ 3" FBM LUX HQ I wonder if it will be firm enough... I'm 180lbs 5'8" with back and neck probs... I do side sleep at times, so softness is key... Any advice? TIA... -Jay |
Re: PU/Latex/Memory Foam Mattress
|
steve2u wrote: I'm still thinking about returning my Sensus topper. I noticed this morning that the spot where I slept throughout the night was like Jello an hour after I got out of bed. The edges of the bed were much more firm. I think that the Sensus topper may be too sensitive to heat for me - it just doesn't seem like it could offer adequate support when it's that soft.
32 ILD latex will be MUCH firmer than the Sensus. A whole different feel, not even in the same ballpark. I don't know if that will be good or bad for you. 32 ILD latex is generally not considered a pure comfort layer. |