The FrankenBed
|
I initially called my creation the FrankenBed because it was made from "parts." The word is taking on a new meaning, as in, I am creating a monster. The basic outline was a latex core, an Intelli-Gel topper from MyComfort, and something in between, possibly 2" of Foamex memory foam. The first major piece to arrive (not counting the foundation on top of a set of Bed Beams), is the latex core. I'll get the Intelli-Gel topper on Monday or Tuesday. I think I might already have a problem. I ordered an ILD 40 Talatech blend core, and I don't think it's going to be firm enough. I initially ordered a 44 but then changed my mind and went with a 40. I should have stayed with the 44. The core actually tested out at an average ILD of 37.8, but I'm not claiming the 2 points is what makes it too soft. Even on 3 2.8" layers, I can bottom out by sitting down on it hard. It's sitting on a concrete floor covered with carpet and I can definitely feel the floor. At the very least, I need to replace one of the ILD 38 layers, and possibly both. I can't bottom out all 4 layers, but that's 11" of latex, and support-wise, it feels pretty soft. Laying on my back, it feels very firm, but it feels like my butt sinks down further than it should. In other words it's almost too soft AND too firm at the same time. Too soft for my butt but too firm for my shoulders. Y'all can go ahead and laugh at me now for thinking I could save money by building my own mattress. Not happenin'. The best that can be said is that maybe my own mistakes can benefit others. I'm debating on what to do. I can be stubborn and order another core, or I can just admit that I made a bad decision and order a support mattress from someone that allows comfort exchanges. I have to allow that even the 44 might not be firm enough, so a money back guarantee would be a good idea too, the second time around. I have some decisions to make. This message was modified Sep 18, 2007 by haysdb
|
Re: The FrankenBed
|
I slept on my new "mattress" last night. The Intelli-Gel didn't do anything to make my latex core feel more supportive, no surprise there, so I need at least one layer of 44. Slightly more surprising is that the Intelli-Gel topper won't quite be the entire comfort layer. So in addition to additional support, I need something more conforming under the topper than the IFD 38 latex. This will either be a softer latex (32? 28?) or memory foam. The flexible slat foundation should be here tomorrow. Presumably that will effect the feel a little bit. |
Re: The FrankenBed
|
haysdb wrote: Slightly more surprising is that the Intelli-Gel topper won't quite be the entire comfort layer. How thick is the gel portion of your topper? Are you primarily a side, stomach, or back sleeper? Thanks for sharing your experiences with this product. |
Re: The FrankenBed
|
I am a 100% side sleeper. The Intelli-Gel in the MyComfort topper is 2.25" thick. It sits on 1" of polyurethane foam. The quilted top adds another 1/2". This message was modified Sep 30, 2007 by haysdb
|
Re: The FrankenBed
| haysdb, too bad about your topper. Did you say it was ordered from Arizona? Mesa AZ is where I went to order my bed. I called the other day to check on my order, and the guy said he was the new manager. Mine is supposed to be in town tomorrow - I sure hope my order is correct. |
Re: The FrankenBed
| When I went to the website to find a dealer, the number I was given happened to be the Arizona location. The topper was actually shipped from a manufacturing or fabrication facility in Salt Lake City Utah. |
Re: The FrankenBed
|
[These next two posts were originally here, but they belong in this thread so I moved them.] tossnturn wrote: So is this a current result of your frankenbed? Any chance of posting some photos? What changes in your purchases would you make '20/20' ? Is the bed heavy with the comfort layer and the mattress core? What is [so far] sleep temp of that layer? With the slat foundation, what is the overall height? Will it fit a headboard? Are you still adjusting it? What pillow seems to work best with your bed so far ? Thanks for all the research time you've put in and posted information.. It will look like a typical mattress when I'm done. Right now it looks like the "prototype" that it is -- Eastern King Intelli-Gel topper sitting on top of naked Cal King latex cores, sitting on top the flexible slat foundation, sitting on the floor of my living room. Once I get a proper mattress cover and the right size Intelli-Gel topper, it will be pretty ordinary looking. This is an image from the Intelli-Gel website:  It is pretty heavy. The flexible slat foundation shipped in three boxes totaling 189 lbs. The Intelli-Gel topper weighs 150 lbs. The latex core weighs ~90 lbs. The total height of the final product will be 19 to 20 inches:
I am still working on it, but I'm pretty close. The "zoning" of the flexible slat foundation has my spine in pretty good alignment, but the Intelli-Gel sitting directly on the ILD 38 latex is a skosh too firm, so I'm contemplating 2" of either memory foam or latex as the top layer of the support mattress. The only pillow I have slept with so far is a Tempur-Pedic body pillow. I sleep on my side and I'm a pillow hugger. I have a RejuveNite (Latex International) shredded latex and down pillow coming Real Soon Now. This message was modified Sep 30, 2007 by haysdb
|
Re: The FrankenBed
|
[This post was originally in this thread, but it belongs in this thread so I moved it.] tossnturn wrote: Thanks for your hard work. Are there 'feet' on the slat foundation? You mentioned to get more of the full 'slat' feeling, a thinner core mattress could be used. Based on your recent discoveries and experience. You would still buy the adjustable slat foundation, mycomfort gel layer, but a thinner core mattress [med or firm?], with a HR foam layer UNDER the gel, but above the core mattress? You seem very close at this point, once it 'fits' a zippered mattress cover will enclose it all. Will you need deep pocket sheets? I think reg is up to 10 inches, deep is up to 15', and very deep up to 18-20', depending on brand. I did not get any feet with my foundation. I did not request any. I upgraded my bed frame to a set of 3 "Bed Beams" which will support the weight of an elephant. However, since the flexible slat foundation is comprised of three sections bolted together, and because the Bed Beams do not provide the recommended center support running head to foot, and because FloBeds recommends 5 slats, two under each head and foot sections, I may add back the two original cross supports I replaced to bring the total to 5. That seems like massive overkill, but they are just going in the trash otherwise so I might as well use them. I definitely like the flexible slat foundation, and I'm pretty sure I'm going to like the Intelli-Gel topper once I get the right amount of cush underneath. The support mattress could be anything. MyComfort sells innerspring, air and memory foam support mattresses that are specifically designed to be used under their Intelli-Gel overlays. I'm doing latex because I liked the feel of Intelli-Bed's $4000 latex mattress. You could do all Pulyurethane, with maybe a layer of HR, or even the more conventional 2.2 or 1.8 lb foam, on the very bottom for the support core and then something like 4 lb Energia (ILD 27), or memory foam, under the overlay. I can't begin to recommend any one of these over another because I haven't tried them all, and you might like something different anyway. The total thickness of the two "mattress" layers will be ~13". My current sheets will fit, but there is no way my fitted sheets will tuck in along the sides because they don't already and my current mattress is only 12" thick, so I will probably buy a couple of deeper fitted sheets. This message was modified Sep 30, 2007 by haysdb
|
Intelli-Gel overlay
|
This ties in with information in this thread, but is here because it specifically relates to the queer way that I'm using my Intelli-Gel "comfort overlay." And before anyone goes off on me, I am not asserting that my creation is superior to an Intelli-Bed or MyComfort mattress. It's just different, OK? The thing I was most interested in was what was attached to what inside the ticking.
I bought the Intelli-Gel overlay hoping to incorporate the Intelli-Gel into my mattress, as just another layer of "stuff" zipped inside a cover. My idea was that when you looked at my mattress, you would see just that - a mattress, and not layers of foam with a skinny mattress stacked on top. Having the Intelli-Gel be a separate "mattress" DOES have it's advantages, namely that a King-size topper weighs 150 lbs. You heard me right. Stack that on top of 90 to 135 lbs of latex, and you have a heavy mattress that would NOT be fun to move as a single mattress. The Intelli-Gel could be removed from the zippered cover for transport, but then you have the very real concern of damaging the foam under and around the Intelli-Gel. But the bottom line is it would easy to slide the Intelli-Gel out of the nice stretch knit topper and lay it right on top of a layer of latex inside a zippered cover. And that's the direction I'm heading.
This message was modified Sep 29, 2007 by haysdb
|
Re: The FrankenBed
|
I think the Intelli-Gel topper needs some additional inches of "comfort layer" between it and the support core for a side sleeper. I have slept four nights now on the Intelli-Gel placed directly over an ILD 38 core, and have experienced some numbness in the arm I'm laying on. I have been debating over what to use. There are at least 8 companies selling a 2" latex topper [1], but only two in anything above a "soft" (22 ILD or less). Since this is a "middle" layer rather than the top-most layer, I think a soft would just be too soft. I ordered a 2" layer of ILD 32 talalay from Foam By Mail. They have a satisfaction guarantee in the event it's too firm. I have found no one selling an ILD 28 topper, so if the 32 is too firm, the next step will have to be a 24. [1] Foam Source, Foam By Mail, Absolute Comfort on Sale, Faom Online, Foam Order, Memory Foam, Sleep Warehouse, and Mattresses.net all offer 2" latex toppers. This message was modified Oct 1, 2007 by haysdb
|
Re: The FrankenBed
|
The 2" ILD 32 latex topper arrived today. My first thought when comparing it to the ILD 38 layers I have is that it was not going to be enough softer to notice, but it is. The feel of the mattress is still "firm" but I experience more of a floating feeling now when I lay on my side. The next step down from the 32 is a 24, as I have never come across an ILD 28 latex topper. My concern, as before, is that would just be too soft, but maybe it wouldn't be as long as the core was properly supportive. In my case along with the slightly more conforming 2" topper is the return of the sinking hips feeling. As I soften up the top, I need to firm up the support layers, so I have asked Dewey if he will sell me an ILD 44 to try. I might also ask Shawn at SleepEZ if he has an ILD 44 dunlop core. If dunlop truly has a higher support factor (something I have never been able to confirm, but it makes sense that it would), then it would be ideally suited to a bottom layer application. I am also anxious to experience the difference between talalay and dunlop first hand. I am really close. I could be very happy with what I have now. I have been sleeping on just the Intelli-Gel over the ILD 38 core for two weeks, and could have lived with that. I have been sleeping through the night and not waking up with any significant aches or pains. But "good enough" isn't why I started this journey, so the quest for "perfection" continues. Interestingly the question of whether 1" of latex or memory foam would make any significant difference arises. I feel like I'm close, really close, and I'm looking for only a very subtle increase in softness. This may be where I get to throw a bit of memory foam into the mix. Conventional wisdom aside, not all memory foam needs body heat. And for this reason, does not have to be used as the top layer in a mattress. I visited a Verlo mattress factory a couple of weeks ago and they use a 1" layer of memory foam between two 1.5" layers of latex in one of their mattresses. This message was modified Oct 10, 2007 by haysdb
|