Mattress Forum

Also, latex has this changeable quality. When one first gets in bed, it feels soft and cushy. By morning, it feels too firm.

 Went to a conventional mattress store today just to see if anything there felt better. Hard to tell with a sore back from the bed I've got.  Oh well, am going to continue to try to make the latex work though.

After trying numerous configurations, I finally concluded that the mattress was probably not firm enough, as it caused back pain, which I didn't suffer from til I purchased this mattress. The last config I tried was the best, but too late, my time was almost up, and the vendor did not wish to extend the time period to help me fine tune it. This was beyond frustrating, as I had diligently worked with the 3 layers in at least 7 combinations to try to make it work, I needed help to handle these 60 lb. pieces of rubber, and it took at least 4 days and more like 2 weeks with each config to tell if it would hurt or cause problems.  It was labor intensive to say the least. I feel like I have spent the last couple of months wrestling with my bed! So I had to return it even though I would have liked to make it work.

I am now back to sleeping on the floor until I can find something else.   The back pain is better, but of course, it is not comfortable.

Many on this forum seem to have been successful with latex, and I too might have gotten there with a little more time and a firmer layer. I think that latex isn't for everyone, or maybe it just takes a lot of tweaking, at this point I will never know.

What I have learned without a doubt is no matter what mattress is purchased, to go with a place that has a refund and return policy, and as long a trial period as possible. Also, if you have an old flippable innerspring, hang on to it and try mattress surgery, because they just don't make them like that anymore and likely never will. 

So I am back to square one, and starting this mattress nightmare search over again.  Today I went to Costco thinking I would just give up and try a cheap s brand again....but then I read the reviews on their site and saw the same old complaints: hurting peoples' backs, smell, too soft, too hard, sagging, etc. It just shouldn't be this hard to find an adequate bed. 

The search, unfortunately, goes on............................

Just get an electric carving knife at Target for $10-15 and measure your latex layer(s) into thirds, then - assuming you have at least 2 layers with different ILD's - just put them so that the firmer part is in the middle and the softer part is at the top. They stay together due to friction, that's not an issue.

That said, it may be that you are one of those people - like my wife and me - who need springs under you. If that's the case, you'll have to buy a spring bed and take the cheap foam out (that's what's off-gassing, most likely) and then take the layers you have and put them over the springs.

http://www.whatsthebest-mattress.com/forum/dissecting-my-sealy-fenway-mattress-bought-costco-4-years-ago-lousy-soft-foam-inside/1954-1-1.html

You can still zone it or not, with the springs.

Thanks for the sympathy. I hope you will keep posting as well when you are ready to move forward and try something new, sounds like we are in the same boat, or at least, a similar one. The last config I tried felt fantastic on the upper body, so it gave me some hope that with a little more time, it might have worked out.

Jim,

I would definitely have tried DIY zoning, but I had to return everything. If i was stuck with my purchase, I would try it as I had nothing to lose. Thanks for the link. As far as sealy innerspring, a reserve level is superior to preferred. I wish I had known to try mattress surgery on my old innerspring. Are you happy with your mattress now?

After I bought an "s" brand and couldn't handle the severe offgassing, i wrote to "s" brand, politely, more than once since no one responded, to let them know my negative experience with their product and to suggest that there was a huge market of people who would love to buy quality, flippable innerspring mattresses. Never heard back, of course. Changing their business strategy would be a great idea, at least to include a line of beds like they used to make, but guess they're not interested. For whoever does jump into the market and do that, I think they will be super profitable. How hard can it be? If I could buy a superior, flippable mattress 15 years ago for less than $200, and considering that the inflation index and wages since then have been relatively flat, such a bed could still be made amd sold economically.  So why the heck is no one doing it?????????? Or if anyone is, where are they?

At this point I would love to find some great springs and have a bed built, but still haven't decided what to do. I'm definitely not a princess, been sleeping on the floor for months now, it just shouldn't be this hard to find a decent mattress that doesn't cause pain or other problems.

Just for the heck of it - The old Spring Air innerspring mattress you liked - was actualy a fairly simple mattress.  It had either a 540 LFK zoned coil in it with the coils zone with 14.5 - 14 - 14.5 gauge coils, or it had a 480 LFK zoned the same.  Coil count based of full size.  Many mattress manufacturers still use these type of coil systems.  The coils were 5.5" tall and were 6 turn units purchased from Leggett & Platt - the biggest spring maker around.

I was at the Spring Air factory in So. Calif. for 11 years.  The Higher coil count was in the higher priced mattresses and, of course, the lower coil count was in the less priced mattresses.

At that point in time they liked to use layers fo convoluted foam - and it seemed to work really well for a lot of people!

A lot of mattress makers have turned to pocketed coils and are using the same 14.5 - 14 - 14.5 gauge configuration.  It also seems to be making a lot of people happy.  BTY - that configuration means that the center third (Aprox.) of the spring unit uses a half gauge thicker wire spring.  depending on the type of coil, height of coil, diameter of the coil, and number of turns in the coil means between a 12 to 19 % increase in support in the center third of the spring unit.

Gunman

Were these old mattresses an open end offset coil, do you know? Or pocketed? They didn't feel like they were pocketed, but don't know.

If 540 or 480 was the coil count for a full, what would be the equivalent for a queen?

Also, they had an almost trampoline like feeling to them, was this because the fiber layers were attached to the spring edges properly, instead of shoehorned into the covers like they supposedly are in beds today? Or were mattresses made using different methods back then?

And finally, the new Spring Air mattresses use similar or same spring systems, but having found one in a local shop here, they don't feel anything like the old ones, and someone told me they are not anything like the old ones. Do you happen to have any info on the new Spring Air mattresses compared to the old? quality?, etc.

Thanks again!

Are that many coils of 14 gauge possibly too much?  Seems almost too firm (being interlaced as well) to really provide much in the way of body conforming comfort.

sorry I'm not gunman, hope he answers again! 

That reserve level is supposedly the best spring system they have for the money....have heard that type spring system it is probably more comfortable for back sleepers, but can work for side sleepers with toppers.