|
I'm going for a pretty soft feel, based on how I liked the Pure Latex bliss nutrition (which is 2" x 19 ild, 2" x 28 ild, 6" x 36 ild) with the 14 ild topper on it. Top to bottom: 2" - 14 ild - $314 - Sleep like a bear 2" - 19 ild - $314 - Sleep like a bear 2" - 28 ild - $204 - Myfoammattress.com 3" - 36 ild - $305 - Myfoammattress.com cover: 10" terrycloth - $85 - Foambymail foundation: EZ-sleep - $215 - bedinabox.com Total: $1437 My concerns are: 1. Will the 3" 36ild base be comparable to the 6" base in the Nutrition, or will it be too little support? My wife and I are about 150 lbs, side sleepers. I figure SleepEZ and Flobeds use 3" base cores, so it should work. 2. Is myfoammattress.com a reputable place to buy from? Prices are good, its Latex International talalay, but not much other info on them. Any comments appreciated - thanks! This message was modified Jun 26, 2011 by proof1st
|
|
For what its worth, I asked Shawn at Sleepez what he recommended for a cover when using split cores, and he says that all you need to do when using the stretch cover is make sure the top layer is 1-piece, not a split layer, to eliminate feeling the seam. He says there wouldnt be any movement of layers since they are rubber, and heavy, they cling together and stay in place. So i guess the one-piece 14ild layer should do the trick in my configuration. This message was modified Jun 29, 2011 by proof1st
|
|
I've decided against the ebay route. Just can't take that kind of risk, just to save a buck. My gut tells me that at least some used cores make it into these sellers inventories. I'm going to step into this slowly - I have a 3" Rejuvenite plush topper (19 ild) on the way, which I will try on top of my current spring mattress and see how that works for a few weeks, then I'll deciding whether I want more softness on top or not. |
|
Proof1st, I think that's a wise plan. I try not to be pennywise and pound foolish either! Let us know how it turns out.
|
| My experience is that anything over 2 inches in soft (for me that would be 24 ild and below) caused lower back pain. I weigh less than you though at 120 pounds, so that probably factors into it. But I would be wary of using any more than 3 inches of soft latex. Good idea to buy in increments! |
|
Not to hijack the thread however, are their other foam solutions that would allow folks to construct a good mattress utilizing latex and these other foams types? Could these types be used for the firmness and the latex (money side) be used for the top half or third of the mattress? Thanks |
|
timby wrote: Not to hijack the thread however, are their other foam solutions that would allow folks to construct a good mattress utilizing latex and these other foams types? Could these types be used for the firmness and the latex (money side) be used for the top half or third of the mattress? Thanks |
| You might want to try memory foam for the top layer instead of latex. We use 2 layers of latex and one layer of memory foam on top with no mattress cover and don't have any problems with movement of the layers. |
|
I think your plan is basically sound, but like others I wonder if you might not have too much soft latex on top. I'm not really sure because I've never tried latex that soft. But I know that in general, more than 2" of too-soft material on top causes me to have lower back pain. Your mileage may vary. I think the 3" foam base will be enough, due to the 3" of 28ILD you have on top of that. As to the question about using other cheaper foams for a base, that is certainly do-able. I used to use HR foam bases with latex on top. I felt that the HR* (similar to HD, not sure what the difference is, both are high quality pu foams) foam gave out much quicker than it is "supposed to". It's rated for 10 years but I felt it was losing it's spring even after just a couple years. But I'd say if you can get it super cheap then it's worth it to just replace it every couple of years. There is also the factor that HR foam just FEELS different than latex. Not necessarily worse, just different. |
|
After some delays in shipping I got the topper and after 1 night on it over the springs, Im pretty happy. We'll see how it goes over time. It is definitely to soft for stomach sleeping, but seems a great middle ground for the combination of back and side sleeping, which works for my wife and me. These rejuvenites have a nice cover - very similar materials to the pure latex bliss with a viscose blend with a little spandex for stretchiness. |