|
i recently went into the brick because im tired of the old one im using now. I decided to buy this one http://www1.thebrick.com/brickb2c/jsp/catalog/product.jsp?prod=WINTERFQP&navAction=jump&navCount=5 after picking it out ive been doing research and alot of people dont like spring air so i dont want to spend good money on something that wont be as good as a different brand like sealy or serta. Has anyone baught this particular set up or can tell me anything interesting about the specs? any advice would be appreciated because i can still cancel the order and pick something else out. thanks |
|
This is probably the actual layering of the obusforme 1 ½”OBUS Firm EcoFoam & an Antimicrobial Silk/Wool Blend. 1” ObusForme® Talalay Latex. 3 ½” OBUS Firm EcoFoam. 1” Deluxe OBUS High Density Fibre Pad. ObusForme® Zoned Individually Encased Coil System. Foam Encased Edge.(foam around the spring for edge support) 9” High Profile ObusForme® EcoBase. You are lighter in weight so 2.5" in the comfort layers could be fairly close to what you need and the firm ecofoam may work well for support underneath (although this would insulate or dominate the springs underneath it). It doesn't give the actual ILD of either the top layer or the Talalay underneath it (very typical) so how it feels would be the best indicator as to it's suitability for you. The "problem" with this mattress is not so much that it couldn't work well for you but more in it's value and durability compared to other mattresses and materials and in it's use of polyfoam in the comfort layers ... although there are other worse "culprits" here. This mattress should last you for longer than a year ... especially give your weight ... and you would likely be looking at several "good" years from it. There is really only 1.5" of poly to worry about (the 3.5" is deeper and not quite as likely to form impressions or degrade as quickly). How long this will last depends entirely on how they made it and it's "specs" ... which of course they don't reveal. There is no memory foam in this which would be my personal biggest concern with outgassing and while polyfoam is made from some pretty toxic chemicals, it is not as "bad" for outgassing as memory foam. There is still the possibility of breathing in the "dust" that comes from poly degrading (this is different from outgassing) but how much of an issue this may be could easily be disputed. You would be "somewhat" protected from this with the ticking. So in terms of "toxicity" there are probably worse things you could be exposed to in the course of life although there are certainly better as well. So given that you are somewhat "locked in" and depending on how you feel about both losing several hundred dollars in an exchange, and sleeping on "less than organic" materials for a few years, it may be worthwhile to consider keeping it. If you are OK with the mattress as it is currenly performing, then perhaps the information you are gathering here could come in very handy whenever you do replace it with something "better". I read your comment that the first night was great and then after not so good. How are things with it now? Phoenix PS: I just realized that your mattress was the plush version so I'm adding a few comments that are about the plush. I'll leave the above up as it may be helpful for someone considering the firm version. This is probably the actual layering of the plush obusforme although the convolute and the latex may be reversed. 1 ½”OBUS Firm EcoFoam & an Antimicrobial Silk/Wool Blend. 1 ½” ObusForme® Pin Convolute. 1” ObusForme® Talalay Latex. 2 ¾” OBUS Firm EcoFoam. 1” Deluxe OBUS High Density Fibre Pad. ObusForme® Zoned Individually Encased Coil System. Foam Encased Edge.(foam around the spring for edge support) This one is a little more "problematic" as there is more foam of the "softer cheaper kind" to break down. It has 4" of comfort layering of which 3" is poly which is a little thick for most people unless they are on the heavier side and have pressure issues. This certainly would feel softer but with the softer thicker poly there is more of the "soft poly" in the comfort layers to break down and the thickness of the comfort layers could present an alignment problem for some people depending on sleeping position, weight, etc. This could be aggravated more quickly as the softer foam breaks down. It would also depend on the zoning a little more with this model as the coils are not quite as "dominated" as in the firm model (although there is still a lot of foam over them) This message was modified Dec 21, 2010 by Phoenix
|
|
My first night on the Spring Air was heavenly compared to my old Ikea foam mattress. Plus I woke up in the morning without pain for the first time in months and practically cried out: "Hallelujah for I am healed!" The next night was great as well. Then, I think it was the third morning when I woke up feeling the same old pain, which now comes and goes. Over all, the mattress is pretty comfortable and the pain has improved. I currently have the new mattress on an Ikea bed frame sans box spring. The frame is not what the Brick salesman described as "standard," i.e., there's no middle support connecting the frame to the ground. This would make my Spring Air warranty null and void were I to complain about sagging one day, which I won't because I plan on tossing the thing and going green. There is a metal support thingy under the slats extending from the head of the frame to the foot. Should I get a new standard frame or else fortify the existing one to prevent sagging in the middle of the mattress? Thanks once again for your advice, Phoenix!
|
|
I have only seen the ikea bedframes via the catalog so I'm not sure what their tendency to sag in the middle may be with a queen. It may also be helpful if you could describe the pain you experience. Is it from pressure (sounds like it could be from description) or from alignment (usually lumbar but could also strain hips, upper back or other areas). If it is from misalignment, then having a very firm and flat base could make a big difference. How firm does it seem to you? I am guessing it is fine. Typically the bedframes that need "floor support" in the middle are the metal ones that go around the edge of a boxspring like this or this. Neither of these are a slatted base like you have and wouldn't be suitable to put directly under a mattress. Perhaps this is what the salesman thought you meant. Slatted bed bases with a midbeam are usually fine. The obus base looks to me like it is a foundation rather than a boxspring which would be very similar to your bedframe. Phoenix Just realized too that you bought the "plush" version which has more of the "soft poly" in it in the comfort layers which may feel softer but could present an alignment problem either now or as the foam degrades. I've added the stats and added a few comments in the previous post. This message was modified Dec 21, 2010 by Phoenix
|
|
Thanks for the info on bed frames, Phoenix. And thanks as well for updating your post on the mattress layering for the plush model. When I had to choose between the firm and plush models, I went for the latter as a reaction to spending a couple years on a 4.5" foam mattress. My thinking was, my outer thighs and hips hurt because there's no cushioning on my old mattress, so I better buy something with a REALLY THICK pillow top. Also, I assumed that extra comfort layers were appropriate for thin types like me (the foam would cushion the bony parts). Yet another example of how some research before purchasing would have helped! I'm assuming that my problems are due to pressure points. Now I have a dumb question for you: how do you know if you are properly aligned? Is it just a feeling or is there a way to check? |
|
You can go by feel or you can have someone look at you as you are laying down in each of your sleeping positions. On your side, your spine should be straight (they can use a yardstick for reference) and on your back (and stomach) it should have the same natural "S" curve as your spine does when you are standing up straight with good posture. It may help to stand up straight and have them look at the natural curve of your spine and then see how close you are laying on your back on the mattress. They should also check that there are no gaps under the recessed parts of your body (shoud be difficult to slide your hand under) in each position you sleep in A proper pillow to keep your head and neck in a proper position is also an important part of alignment Here is a rough example of good and poor alignment on a mattress Phoenix This message was modified Dec 22, 2010 by Phoenix
|
|
Great info on alignment, Phoenix. The illustration really helps. I think I'm fine for now in this regard. I used my new Natura pillow last night for the first time and it gave me great support (I just have to get used to the smell, which, though less than pleasant, is at least non-toxic!) Out of curiosity, I checked out some "natural latex" mattresses while I was Christmas shopping. Went into the Keetsa shop ( I noticed that the products are made in China...not very environmentally friendly for a self-promoting "green" company!) Someone like you should write a "Dummies Guide to Buying a Mattress" or an online manual that, for a small fee, helps to cut through all the misinformation and hype...or else a documentary expose on the industry. |
|
Keetsa ... IMO ... is a prime example of "greenwashing". This is not to say their products are bad ... but to call "green tea" memory foam "green" because they've replaced a little bit of their oil based polyols with plant based polyols is a little like saying just try this "reduced arsenic" drink. It tastes great and has less of the bad stuff in it. Their latex is probably an example of some of the latex I was referring to in the Ikea thread. This too is not bad as there seems to be some very good latex coming out of Asia (both Talalay and Dunlop) but there is also some "not very good" latex coming from the same area. It certainly makes it more difficult to know what you are getting. I wish they (and others) would be more open about the source of their latex ... but of course this could take away the "story" that sells their mattresses. Phoenix This message was modified Dec 24, 2010 by Phoenix
|
|
I am so glad I found this thread! We are considering the Spring Air Obusforme Winter firm ... we have a $1200 credit to use @ the Brick and would welcome any advice on the best way to use it ... we have had a string of bad luck with mattresses and wish we had went the DIY route to start ... We have learned from our mistakes and realize that we don't want a thick topper or a plush unsupportive mattress! |