Talalay latex - 2, 3, or 4 layers?
|
I seem to remember a post some time ago which discussed how to decide how many layers to go with. But I can't find it! Anyone remember this? Or can help me out now? Me - 5'6", 160, side and stomach sleeper. Husband - 5'10", 170, stomach sleeper. I definitely like more cushion than my husband. I'm thinking to put these latex layers on top of our current box spring, whcih seems to be in good condition (and is attached nicely to our iron bed :) Also, I'm thinking either Firm or X Firm core - any advice here? Susan |
Re: Talalay latex - 2, 3, or 4 layers?
|
Thanks for the info Cloud. I guess we'll try the boxspring and if there's issues, we can switch out then. Anyone else have any input on how to choose 2, 3, or 4 layers? This message was modified Oct 8, 2007 by suz312
|
Re: Talalay latex - 2, 3, or 4 layers?
| Suz312, I chose three latex cores and a topper for the height of the mattress and for the ability to move more cores around to get the exact feel I wanted. I have been very happy with FloBeds 90 day exhange policy and customer support. I love my bed so much and I love the 10" legs over the slat box. I really feel latex needs a solid surfact to be on top of like I have now. Good luck in whatever decision you make. |
Re: Talalay latex - 2, 3, or 4 layers?
|
For stomach sleeping I like: 2" 32 ILD top 3" 36 ILD middle 3" 44 ILD bottom I do not like that configuration for side sleeping. I can't imagine any configuration that would be firm enough for stomach sleeping and soft enough for side sleeping. That is a very difficult combination. I think you should focus on one or the other and build to that goal if possible. |
Re: Talalay latex - 2, 3, or 4 layers?
| This combination sounds like the SleepEZ medium, firm, extra firm configuration. That's pretty firm and a good place to start for someone who likes a firm bed. I found it completely avoided the hammocking issue softer Talalay configurations are prone to, but if you don't have much padding on your hips it can feel pretty hard for side sleeping,so you might want to add a 1.5 to 2" topper of softer latex. Try it without first. |
Re: Talalay latex - 2, 3, or 4 layers?
| Has anyone used only 1 layer? I have been planning to get 6" of 36 ILD latex over a flexible slat foundation, with the possibility of adding a 1" or 2" topper if the bed feels to firm. Is there anything wrong with just 1 core or should I be getting 2-6" cores? Cost is the only reason I am shying away from 2 cores, as that would cost...twice as much. |
Re: Talalay latex - 2, 3, or 4 layers?
| The Thickness of Latex Cores from FloBeds.com and SleepEZ.com are from 2.8" (for blended latex) to 3.0" (for natural latex) so a 6" core would be like you having two latex cores. I think that would be fine with a topper over a slat box or platform bed. I would not put latex on top of a box spring since latex needs a very firm solid foundation. |
Re: Talalay latex - 2, 3, or 4 layers?
|
The flexible slat foundation definitely lets you get away with a thinner mattress. It almost totally eliminates any "bottoming out," even with only a single 5.6" latex core. In fact, the thicker the mattress, the less effect the flexible slat foundation will have, so you won't want to go over about 8". IMO. The trick with a solid core is getting the right firmness. The benefit of "half cores" is you can adjust simply by changing the order of the layers. I bought an ILD 40 core because I was afraid 44 would be too firm and 36 too soft. In fact, I would have been better served in buying two "half cores," one of 36 and one of 44. That would have given me two choices of firmness: 36/44 and 44/36. Technically a "core" is 5.6" or 6" thick. This term is also used by Flobeds to refer to what is essentially a quarter core since it's half as thick and half as wide as a full core. MequonJim and Cloud9, your comments reflect my experience as well. I am sleeping on 38, 38, 32 and it's pretty firm for side sleeping. It's tricky though. On a solid platform I felt like my hips were sinking while at the same time it was too firm for my shoulders. It's a balancing act to get both support AND pressure point relief simultaneously with a foam mattress. This message was modified Oct 17, 2007 by haysdb
|
Re: Talalay latex - 2, 3, or 4 layers?
|
Today I stopped by a foam store to try out beds. They don't have layering systems set up. They sell the 6" cores + toppers. They had one bed with only one firm core + padded case and it felt pretty good. I'd say you could definitely go with just one layer, so long as it's the right firmness for you. The only thing to keep in mind is that it will be just 6 or so inches high - it looks kinda short, but really no shorter than the old conventional mattresses. The configuration I really liked was 1 6" core + 1 3" topper + 1 padded case (wool, muslin, cotton). It was 100% natural dunlop, and a little on the soft side. So now I'm debating about whether to go with that, or find a similar Talatech combination, which might last longer. |
Re: Talalay latex - 2, 3, or 4 layers?
| I wouldn't worry about the natural dunlop not holding up. Sears sold latex mattresses in the 60's that are still in use today. Here is a page that shows some pictures of these mattresses and their mattress tags showing when they were manufactured. Click the pause button on the annoying Flash animation at the top of the page. |
Re: Talalay latex - 2, 3, or 4 layers?
|
Dunlop latex is very different in feel from Talalay. I slept on a Dunlop for over 20 years. I don't even think it was 6" thick and was sold with a boxspring. Having slept on both Dunlop and Talalay I have to say I really prefer the Dunlop. Talalay can be tricky to configure. Too firm and it can feel like it's excerting pressure on your body. Too soft, your hips sink in. Dunlop on the other hand doesn't share any of these characteristics. I think with Talalay it's absolutely necessary to build a mattress out of several layers of different ILD's. With Dunlop it's possible to get support and comfort all in the same layer. I can say from experience that Dunlop will last a long, long time. I had mine for 20 years before the mattress started to dry up and slowly disintegrate. This message was modified Oct 19, 2007 by cloud9
|